On a dot matrix printer, you should never lubricate which part?

  1. Home

Question:
On a dot matrix printer, you should never lubricate which part?

1.carriage rails

2.printhead pins

3. paper advance bearings

4.carriage bearings

Posted Date:-2021-02-20 05:29:00

More MCQS Questions and answers

  1. In a computer with an eide adapter, where should you connect an ATA CD-ROM drive?
  2. IRQ6 is typically reserved for:
  3. Which device uses a DMA channel?
  4. SCSI must be terminated with?
  5. What could cause a fixed disk error?
  6. What is the highest binary number that can be referred to on a three position jumper block?
  7. What's the best way to prevent damaging your PC with static electricity?
  8. Which of the following FRUs would be considered both an input/output device?
  9. Which of the following would be a logical first step in troubleshooting a PC?
  10. Which should you use for cleaning Mylar-protected LCD screens?
  11. Which would you do first when troubleshooting a faulty monitor?
  12. ____ help prevent power surges.
  13. A COM port is a _____ port.
  14. A modem could be attached to which port?
  15. A system has two IDE hard drives that are each divided into primary and extended partitions, which drive letter is assigned to the primary partition of the second drive?
  16. After trying to unload a TSR, you get an error message saying that other TSRs were loaded after the one you tried to remove. Which of the following commands could you use to see the current load order?
  17. An anti static strap uses a small _____ to make sure you do not become the least path of resistance to the ground?
  18. During boot-up, the memory test:
  19. ESD potential decreases with the use of:
  20. For a Macintosh to print successfully, the System Folder must contain:
  21. he digital multimeter is set for DC, Ohm and 20k. You will read _____ while measuring a good 2 amp fuse.
  22. How many devices can be used on a single SCSI bus? Keep in mind that the SCSI host adapter counts as a device.
  23. What's the best way to protect your hard drive data?
  24. If the memory slots have 30 pins then the chip is a?
  25. Laser Jet printer speeds are measured in pages per minute (ppm) what do we use to measure dot-matrix printers?
  26. Match the device driver HIMEM.SYS to its operation.
  27. On a dot matrix printer, you should never lubricate which part?
  28. On the 16-bit ISA bus, IRQ2 is elevated to which higher level interrupt?
  29. To install a second IDE drive into a computer, you must
  30. To test for AC ripple on a PC power supply, you would set the volt/ohm meter for:
  31. What device prevents power interruptions, resulting in corrupted data?
  32. What do you need to check serial and parallel port?
  33. What is a common language that computers use to talk with one another on a network
  34. What is the first step in diagnosing a completely dead computer at the client site that was working the day before.
  35. What is the most significant difference between the USB and IEEE1394 standards?
  36. What specification covers PC hard cards?
  37. When connecting a ribbon cable to a connector, how do you know which direction to plug it in?
  38. When connecting two internal SCSI hard disks to a computer, where do you connect the second hard drive?
  39. When is the risk for electrostatic discharge the greatest?
  40. Which component must be vacuumed or replaced during preventative maintenance on a laser printer?
  41. Which device is on IRQ 6?
  42. Which DOS driver is used to emulate expanded memory?
  43. Which values are held in CMOS for the hard drive
  44. Why does a successfully mapped network drive disappear every time you boot the computer?
  45. You get a CMOS checksum error during bootup. What is most likely the cause?
  46. You have a PC with no video* Which of the following is LEAST likely to be causing the problem?
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!