Block coding can help in _______ at the receiver.

  1. Home

Question:
Block coding can help in _______ at the receiver.

1.Synchronization

2.Error detection

3.Attenuation

4. both (a) and (b)

Posted Date:-2022-06-17 06:11:40

More MCQS Questions and answers

  1. If the bit rate for an ASK signal is 1200 bps, the baud rate is ________.
  2. In ______ schemes, the voltages are on the both sides of the time axis. For example, the voltage level for 0 can be positive and the voltage level for 1 can be negative.
  3. In a _____ scheme, all the signal levels are on one side of the time axis, either above or below.
  4. In QAM, both ________ of a carrier frequency are varied.
  5. The _____ scheme uses data patterns of size 2 and encodes the 2-bit patterns as one signal element belonging to a four-level signal.
  6. The idea of RZ and the idea of NRZ-I are combined into the ________ scheme.
  7. The signal rate is sometimes called the ____ rate.
  8. Which quantization level results in a more faithful reproduction of the signal?
  9. _ provides synchronization without increasing the number of bits.
  10. ____ finds the value of the signal amplitude for each sample; ____ finds the change from the previous sample.
  11. _____ provides redundancy to ensure synchronization and inherent error detection.
  12. _____ substitutes eight consecutive zeros with 000VB0VB. a.
  13. ______ is normally referred to as mB/nB coding; it replaces each m-bit group with an n-bit group.
  14. ______ substitutes four consecutive zeros with 000V or B00V.
  15. _______ encoding has a transition at the beginning of each 0 bit.
  16. ________ is the process of converting digital data to a digital signal.
  17. ___________ conversion involves three techniques: line coding, block coding, and scrambling.
  18. A _________ digital signal includes timing information in the data being transmitted.
  19. AM and FM are examples of ________ conversion.
  20. ASK, PSK, FSK, and QAM are examples of ________ conversion.
  21. Block coding can help in _______ at the receiver.
  22. If the baud rate is 400 for a QPSK signal, the bit rate is ________ bps.
  23. If the bit rate for an FSK signal is 1200 bps, the baud rate is ________.
  24. If the frequency spectrum of a signal has a bandwidth of 500 Hz with the highest frequency at 600 Hz, what should be the sampling rate, according to the Nyquist theorem?
  25. In ______ transmission, we send 1 start bit (0) at the beginning and 1 or more stop bits (1s) at the end of each byte.
  26. In _______ encoding, the duration of the bit is divided into two halves. The voltage remains at one level during the first half and moves to the other level in the second half. The transition at the middle of the bit provides synchronization.
  27. In _______ transmission, a start bit and a stop bit frame a character byte.
  28. In _________ transmission, we send bits one after another without start or stop bits or gaps. It is the responsibility of the receiver to group the bits.
  29. In ___________ there is always a transition at the middle of the bit, but the bit values are determined at the beginning of the bit. If the next bit is 0, there is a transition; if the next bit is 1, there is none.
  30. In _______encoding, we use three levels: positive, zero, and negative.
  31. In ______, the change or lack of change in the level of the voltage determines the value of the bit.
  32. In _____, the level of the voltage determines the value of the bit.
  33. In asynchronous transmission, the gap time between bytes is _______.
  34. In decoding a digital signal, the receiver calculates a running average of the received signal power, called the _______.
  35. In Manchester and differential Manchester encoding, the transition at the middle of the bit is used for __________.
  36. PCM is an example of _______ conversion.
  37. The ______ scheme uses three levels (+V, 0, and -V) and three transition rules to move between the levels.
  38. The ________ mode provides synchronization for the entire stream of bits must. In other words, it guarantees that the data arrive at a fixed rate.
  39. The ________ rate defines the number of data elements sent in 1s; the ______ rate is the number of signal elements sent in 1s.
  40. The data rate is sometimes called the ___ rate.
  41. The first step in PCM is ________.
  42. The idea of RZ and the idea of NRZ-L are combined into the ________ scheme.
  43. The minimum bandwidth of Manchester and differential Manchester is ____ that of NRZ.
  44. The most common technique to change an analog signal to digital data is called __________.
  45. The Nyquist theorem specifies the minimum sampling rate to be_______.
  46. There are three sampling methods: __________.
  47. Two common scrambling techniques are ________.
  48. Which encoding method uses alternating positive and negative values for 1s?
  49. Which of the following encoding methods does not provide for synchronization?
  50. While there is (are) only _____ way(s) to send parallel data, there is (are) three subclass(es) of serial transmission.
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!