The code does not suggests reduction factor for shear capacity in the case

  1. Home
  2. Back

Question:
The code does not suggests reduction factor for shear capacity in the case

1. if the joint is too long

2.if number of bolts exceeds a specified number

3.if the grip length is large

4. if packing plate thickness exceeds 6 mm

Posted Date:-2022-09-28 03:40:41

More MCQS Questions and answers

  1. rivet hole diameter
  2. A butt weld is specified by
  3. A channel section has
  4. A steel beam supporting loads from the floor slab as well as from wall is termed as
  5. According to tension field method as web begins to buckle
  6. At a fully plastic section, infinite rotation can occur at
  7. Bending compressive and tensile stresses respectively are calculated based on
  8. Bolts are most suitable to carry
  9. Column splice plates may be assumed to act as columns with slenderness ratio
  10. Economical depth of a plate girder corresponds to
  11. For compression members most preferable I-section is
  12. For connecting circular tubes in tension, the best connection is by
  13. For HSFG bolts, partial safety factor designed at service load and at ultimate load are respectively
  14. For welded and double laced joints, effective length of lacing is _____ times the actual length.
  15. Gantry girders are designed to resist
  16. Hudson's formula gives the dead weight of a truss bridge as a function of
  17. If a plate with small hole is kept over another plate and the entire hole is filled with weld material, the welded joint is known as
  18. In a compression member of a truss, consisting of double angle, tacking bolts should be provided at a distance not more than
  19. In designing connection between web plate and flange plate, shear stress is calculated using moment of inertia of
  20. In roof trusses bracings should be provided at top chord level in the
  21. In the design of a connection of tension member to a gusset plate, the principle to be followed is
  22. In the virtual work method, the virtual quantity is
  23. Lacing and battening of columns is to increase _____ of column.
  24. Load carrying capacity of compression member depends upon
  25. Load factor is
  26. Maximum spacing of lacing bars shall be such that the maximum slenderness of the main member between consecutive lacing connection is not more than
  27. Maximum width of steel plates manufactured are
  28. Minimum edge distance specified by the code should be maintained to avoid
  29. Minimum edge distance, in case of hand flame cut edges, shall not be less than _____ times bolt hole diameter.
  30. Minimum thickness of rolled steel flats available is
  31. Racking force on a steel railway bridge is due to
  32. Rolled steel tubes are referred by their
  33. Steel tanks are mainly designed for
  34. The advantage of steel structure is
  35. The beam sections in which the extreme fibre in compression can yield stress, but cannot develop the plastic moment of resistance, due to local buckling are classified as
  36. The best arrangement to provide unified behavior in built up steel columns is by
  37. The bracing provided in the plane of end posts is called
  38. The capacity of the smallest pressed steel tank is
  39. The code does not suggests reduction factor for shear capacity in the case
  40. The effect of axial force and shear force on the plastic moment capacity of a section are
  41. The effective diameter of a river is taken as
  42. The effective length of a fillet weld should not be less than
  43. The forces acting on the web splice of a plate girder are
  44. The moment curvature relation at a plastic hinge is
  45. The most economical section for a compression member is
  46. The stress at which a material fractures under large number of reversals of stress is called
  47. The successful introduction of _____ bolts resulted into replacement of rivets.
  48. The use of tie plates in laced columns is
  49. The weakest plane in a filler weld is
  50. To connect members subjected to dynamic loads which one of the following type of bolts is preferable?
  51. When the two columns to be spliced are of slightly different size
  52. Which of the following conditions is to be satisfied both in elastic and plastic analysis?
  53. Which of the following sections should preferably be used at places where torsion occurs?
  54. Which of the following types of riveted joint is free from bending stresses?
  55. Which one of the following is not a flexible connection of beams?
  56. Which one of the following is not a variable action?
  57. Which one of the following is not an advantage of bolted connection over welded connection?
  58. Which one of the following is not limit state of serviceability?
  59. Which one of the following is not the advantage of HSFG bolt?
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!