The effective stress in wire ropes during normal working is equal to the stress due to

  1. Home
  2. Back

Question:
The effective stress in wire ropes during normal working is equal to the stress due to

1. Axial load plus stress due to bending

2.Acceleration/retardation of masses plus stress due to bending

3. Axial load plus stress due to acceleration/retardation

4.Bending plus stress due to acceleration/retardation

Posted Date:-2021-11-27 14:45:59

More MCQS Questions and answers

  1. 18/8 steel contains
  2. A bolt is designed on the basis of __________ with a large factor of safety.
  3. A bolt of M 24 × 2 means that
  4. A column of length l is fixed at both ends. The equivalent length of the column is
  5. A feather key is generally
  6. A hollow saddle key is
  7. A special case of ductility which permits materials to be rolled or hammered into thin sheets, is called
  8. A tapered key which fits in a key way in the hub and the bottom of which is shaped to fit the curved surface of the shaft, is known as,
  9. A type of brake commonly used in motor cars is a
  10. For a bevel gear having the pitch angle θ, the ratio of formative number of teeth (TE) to actual number of teeth (T) is
  11. For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately
  12. If a spring is cut down into two springs, the stiffness of cut springs will be
  13. If the centre distance of the mating gears having involute teeth is varied within limits, the velocity ratio
  14. In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft)
  15. In second type of levers,
  16. In the levers of third type, the mechanical advantage is __________ one.
  17. In V-belt drive, belt touches
  18. Rankine Gordon formula for buckling is valid for
  19. Stress concentration is caused due to
  20. The maximum efficiency of a square threaded screw is
  21. The ratio of driving tensions for flat belts, neglecting centrifugal tension, is (where T₁, and T₂ = Tensions on the tight and slack sides of belt respectively, μ = Coefficient of friction, between the belt and pulley, and θ = Angle of contact)
  22. The size of a cam depends upon
  23. When the screw in a mechanical screw jack rotates, the load kept on the top of it moves
  24. Which of the following property is essential for spring materials?
  25. While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as
  26. . The distribution of the forces along the length of key fitted in a shaft
  27. A compound cylinder with inner radius 50 mm and outer radius 70 mm is made by shrinking one cylinder on to the other cylinder, the junction radius is 60 mm and the junction pressure is 1.1 N/mm². The maximum hoop stress developed in the inner cylinder is
  28. A double fillet welded joint with parallel fillet weld of length ‘l’ and leg ‘s’ is subjected to a tensile force ‘P’. Assuming uniform stress distribution, the shear stress in the weld is given by
  29. A key way lowers
  30. According to I.B.R., the factor of safety of riveted joint should not be less than
  31. According to I.B.R., when the thickness of the boiler shell (t) is less than 8 mm, then the diameter of the rivet hole (d) is obtained by
  32. According to Indian standard specifications, 100 H6/g5 means that
  33. According to Indian standard specifications, a Grey cast iron designated by 'FG 200' means that the (A)
  34. Aircraft body is usually fabricated by
  35. Allen bolts are
  36. An open coiled helical compression spring 'A' of mean diameter 50 mm is subjected to an axial load ‘W’. Another spring 'B' of mean diameter 25 mm is similar to spring 'A' in all respects. The deflection of spring 'B' will be __________ as compared to spring 'A'.
  37. Belt slip may occur due to
  38. If the centre distance of the mating gears having involute teeth is increased, then the pressure angle
  39. In a butt welded joint, the size of weld is __________ the throat of weld.
  40. In a gear, having Involute teeth, the normal to the Involute is a tangent to the
  41. In a marine flange coupling, the pitch circle diameter of bolts is taken as
  42. In levers, leverage is the ratio of
  43. In oilness bearings
  44. In order to determine the stresses in a thin cylinder due to an internal pressure, it is assumed that
  45. Oldham coupling is used to connect two shafts
  46. The acme threads are usually found on
  47. The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to
  48. The bending stress in a curved beam is
  49. The circumferential and longitudinal strains in a cylindrical boiler under internal steam pressure are εc and εl respectively. The change in volume of the boiler cylinder per unit volume will be
  50. The coefficient of friction in belt drive depends upon
  51. The connecting rod bolts are tightened up so that tightening stress
  52. The connecting rod bolts are tightened up with initial tension greater than the external load so that
  53. The cross-section of the arm of a bell crank lever is
  54. The effective stress in wire ropes during normal working is equal to the stress due to
  55. The face of the tooth is the
  56. The form factor of a helical gear __________ with the increase in the helix angle.
  57. The helix angle for double helical gears may be made up to
  58. The included angle for the V-belt is usually
  59. The material used for brake lining should have __________ coefficient of friction. (A) (B) (C)
  60. The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as
  61. The objective of caulking in a riveted joint is to make the joint
  62. The process which improves the machinability of steels, but lowers the hardness and tensile strength is
  63. The radial distance of a tooth from the pitch circle to the top of the tooth is called
  64. The resistance to fatigue of a material is measured by
  65. The resultant axial load on a bolt depends on
  66. The width of the pulley should be __________ width of the belt.
  67. Two closely coiled helical springs with stiffness k₁ and k₂ respectively are connected in series. The stiffness of an equivalent spring is given by
  68. Two shafts ‘A’ and ‘B’ under pure torsion are of identical length and identical weight and are made of the same material. The shaft ‘A’ is solid and the shaft ‘B’ is hollow. We can say that
  69. Wahl's stress factor __________ very rapidly as the spring index decreases.
  70. When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is
  71. When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor, and W = Axial compressive load on the spring)
  72. When carbon in the cast iron is principally in the form of graphite, the cast iron will be of
  73. When the length of the journal is equal to the diameter of the journal, then the bearing is said to be a
  74. Which of the following has threads at both ends?
  75. Which of the following spring is used in mechanical wrist watch?
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!