Engineering/Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1 Sample Test,Sample questions

Question:
 
A compacted soil sample using 10% moisture content has a weight of 200 g and mass unit weight of 2.0 g/cm3. If the specific gravity of soil particles and water are 2.7 and 1.0, the degree of saturation of the soil is

1.11.10%

2.55.60%

3.69.60%

4. none of these.

Posted Date:-2021-05-13 08:33:06


Question:
 
Accurate determination of water content, is made by

1.calcium carbide method

2. sand bath method

3.alcohol method

4.oven-drying method.

Posted Date:-2021-05-13 08:33:06


Question:
 
Pick up the correct statement from the following:

1. Sandy clayloam contains highest percentage of sand

2.Silty clayloam contains highest percentage of silt

3.Stiff boulder clay offers maximum shear strength

4.Soft chalk carries least safe load

Posted Date:-2021-05-13 08:33:06


Question:
 
The liquid limit and plastic limit exist in

1.sandy soils

2.silty soils

3.gravel soils

4.clay soils.

Posted Date:-2021-05-13 08:33:06


Question:
 
The ratio of the volume of voids to the volume of soil solids in a given soil mass, is known

1.porosity

2. specific gravity

3.void ratio

4.water content.

Posted Date:-2021-05-13 08:33:06


Question:
  
According to Coulomb's wedge theory, the active earth pressure slides the wedge

1.down and outwards on a slip surface

2.up and inwards on a slip surface

3.horizontal upward and parallel to base

4.horizontal inward and parallel to base.

Posted Date:-2021-05-13 08:33:06


Question:
  
Failure of the stability of slopes, generally occurs along

1.slip plane

2.a horizontal surface

3.a curved surface

4. all the surfaces.

Posted Date:-2021-05-13 08:33:06


Question:
  
Minimum size of the particles of silt soil, is

1. 0.002 mm

2. 0.04 mm

3.0.06 mm.

4.0.08 mm

Posted Date:-2021-05-13 08:33:06


Question:
  
Pick up the clay soil group which does not swell when wet from the following :

1.Kaolinite group

2.Illite group

3.Vermiculite group

4.Montrorillonite group.

Posted Date:-2021-05-13 08:33:06


Question:
  
Stoke's law sates that the velocity at which a grain settles out of suspension, the other factors remaining constant, is dependent upon

1.shape of grain

2.weight of grain

3.size of grain

4.shape, size and weight of grain.

Posted Date:-2021-05-13 08:33:06


Question:
  
The clay soil mainly consists of

1.Kaolinites

2.Montomorillonite

3.Illites

4.All the above.

Posted Date:-2021-05-13 08:33:06


Question:
  
The weight of a pycnometer containing 400 g sand and water full to the top is 2150 g. The weight of pycnometer full of clean water is 1950 g. If specific gravity of the soil is 2.5, the water content is

1.5%

2.10%

3.15%

4.20%

Posted Date:-2021-05-13 08:33:06


Question:
A coarse-grained soil has a voids ratio 0.75, and specific gravity as 2.75. The critical gradient at which quick sand condition occurs, is

1.0.25

2.0.5

3.0.75

4.1

Posted Date:-2021-05-13 08:33:06


Question:
A partially saturated sample of soil has a unit weight of 2.0 g/cm3 and specific gravity of soil particles is 2.6. If the moisture content in the soil is 20%, the degree of saturation is

1.20%

2.77%

3.92%

4. none of these.

Posted Date:-2021-05-13 08:33:06


Question:
Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H and acts at

1. H/4 above the base parallel to base

2.H/2 above the base parallel to base

3.H/3 above the base parallel to base

4. H/5 above the base parallel to base.

Posted Date:-2021-05-13 08:33:06


Question:
Degree of saturation of a natural soil deposit having water content 15%, specific gravity 2.50 and void ratio 0.5, is

1.50%

2.60%

3.75%

4.80%

Posted Date:-2021-05-13 08:33:06


Question:
Factor of safety against sliding of a slope, is the ratio of

1.actual cohesion to that required to maintain stability of slope

2.shear strength to shear stress along the surface

3. neither (a) nor (b)

4.both (a) and (b).

Posted Date:-2021-05-13 08:33:06


Question:
Geologic cycle for the formation of soil, is

1.Upheavel → transportation → deposition → weathering

2.Weathering → upheaval → transportation → deposition

3.Transportation → upheaval → weathering → deposition

4.Weathering → transportation → deposition → upheaval

Posted Date:-2021-05-13 08:33:06


Question:
If the failure of a finite slope occurs through the toe, it is known as

1.slope failure

2.face failure

3. base failure

4.toe failure.

Posted Date:-2021-05-13 08:33:06


Question:
In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil, is

1.35%

2.50%

3.65%

4.none of these.

Posted Date:-2021-05-13 08:33:06


Question:
Pick up the correct statement from the following :

1.In soils, the flow index indicates variation in shear strength with water content

2.Liquid limit minus plastic limit, is known as plasticity index of the soil

3.Plastic limit minus shrinkage limit, is known as shrinkage index of the soil

4.All the above.

Posted Date:-2021-05-13 08:33:06


Question:
Pick up the correct statement from the following:

1.When water table is above the base of a footing, the dry weight m should be used for soil below water table

2. When water table is located somewhat below the base of a footing, the elastic wedge is partly of moist soil and partly of submerged soil, and a suitable reduction factor is used

3.When water table is just at the base of the footing, no reduction factor is used

4.None of these.

Posted Date:-2021-05-13 08:33:06


Question:
Pick up the correct statement from the following:

1.Failure plane carries maximum shear stress

2.Failure plane does not carry maximum shear stress

3.Failure plane carries shear stress equal to maximum shear stress

4.None of these.

Posted Date:-2021-05-13 08:33:06


Question:
Pick up the correct statement from the following:

1. The rise of the ground surface due to frost action is called frost heave.

2.The freezing of water is accompained by a volume increase of 9%.

3.Below freezing point, higher soil suction develops.

4.All the above.

Posted Date:-2021-05-13 08:33:06


Question:
Rankine's theory of active earth pressure assumes

1.soil mass is homogeneous, dry and cohesionless

2.ground surface is a plane which may be horizontal or inclined

3. back of the wall is vertical and smooth

4.all the above.

Posted Date:-2021-05-13 08:33:06


Question:
The coefficient of compressibility of soil, is the ratio of

1.stress to strain

2.strain to stress

3.stress to settlement

4.rate of loading to that of settlement.

Posted Date:-2021-05-13 08:33:06


Question:
The fluid generally used for grouting is

1.cement and water mix

2.clay suspension

3.sodium silicate

4. all the above.

Posted Date:-2021-05-13 08:33:06


Question:
The internal molecular attraction of a soil, the cohesion

1.decreases as the moisture content increases

2. increases as the moisture content decreases

3. is more in well compacted clays

4.depends upon the external applied load.

Posted Date:-2021-05-13 08:33:06


Question:
The lateral earth pressure on a retaining wall

1.is equal to mass of the soil retained

2.proportional to the depth of the soil

3. proportional to the square of the depth of the soil

4. proportional to the internal friction of the soil

Posted Date:-2021-05-13 08:33:06


Question:
The liquidity index is defined as a ratio expressed as percentage of

1.plastic limit minus the natural water content, to its plasticity index

2.natural water content minus its plastic limit to its plasticity index

3.natural water content plus its plastic limit to its plasticity index

4.liquid limit minus the natural water content to the plasticity index.

Posted Date:-2021-05-13 08:33:06


Question:
The maximum value of effective stress in the past divided by the present value, is defined as over consolidation ratio (OCR). The O.C.R. of an over consolidated clay is

1.less than 1

2.1

3. more than 1

4.None of these.

Posted Date:-2021-05-13 08:33:06


Question:
The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known

1.liquid limit

2.plastic limit

3.shrinkage limit

4. permeability limit.

Posted Date:-2021-05-13 08:33:06


Question:
The minimum water content at which the soil retains its liquid state and also possesses a small shearing strength against flowing, is known

1.liquid limit

2.plastic limit

3.shrinkage limit

4.permeability limit.

Posted Date:-2021-05-13 08:33:06


Question:
The quantity of seepage of water through soils is proportional to

1. coefficient of permeability of soil

2.total head loss through the soil

3.neither (a) nor (b)

4.both (a) and (b).

Posted Date:-2021-05-13 08:33:06


Question:
The ratio of the weight of given volume of soil solids to the weight of an equal volume of distilled water at the given temperature, is known

1.porosity

2. specific gravity

3.void ratio

4.water content.

Posted Date:-2021-05-13 08:33:06


Question:
The seepage force in a soil, is

1.perpendicular to the equipotential lines

2.proportional to the exit graident

3. proportional to the head loss

4. all the above.

Posted Date:-2021-05-13 08:33:06


Question:
The ultimate Settlement of a soil is directly proportional to:

1.depth of the compressible soil strata

2.compressive index

3.void ratio

4.both (a) and (b)

Posted Date:-2021-05-13 08:33:06


Question:
The water content of soil is defined as the ratio of

1.volume of water to volume of given soil

2.volume of water to volume of voids in soil

3.weight of water to weight of air in voids

4. weight of water to weight of solids of given mass of soil.

Posted Date:-2021-05-13 08:33:06


Question:
Under-reamed piles are generally

1.driven piles

2.bored piles

3.precast piles

4.all the above.

Posted Date:-2021-05-13 08:33:06


Question:
When drainage is permitted under initially applied normal stress only and full primarily consolidation is allowed to take place, the test is known as

1.quick test

2.drained test

3.consolidated undrained test

4.none of these.

Posted Date:-2021-05-13 08:33:06


Question:
Which one of the following statements is true ?

1.Clays are more porous than sands

2.Pressure of organic matter in a soil decreases the bearing capacity of the soil

3.Aluminous cement is used for foundations in soils with chemical deposits

4.All the above.

Posted Date:-2021-05-13 08:33:06


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
  106. Basic Civil Engineering MCQ
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!