Engineering/Civil%20Engineering%20MCQS-Surveying%20Section%207 Sample Test,Sample questions

Question:
 
If + 0.8% grade meets - 0.7% grade and the rate of change of grade for 30 m distance is 0.05, the length of the vertical curve will be

1.600 m

2.700 m

3.800 m

4.900 m

Posted Date:-2021-05-13 08:27:18


Question:
 
If the chain line which runs along N-S direction is horizontal and the ground in E-W direction is sloping

1. it is possible to set offsets correctly on east side

2.it is possible to set offsets correctly on east side

3.it is not possible to set offsets correctly on west side

4.it is possible to set offsets correctly on both sides.

Posted Date:-2021-05-13 08:27:18


Question:
 
The properties of autogenous curve for automobiles are given by

1.true spiral

2.cubic parabola

3.Bernoulli's Lemniscate

4. clothoid spiral.

Posted Date:-2021-05-13 08:27:18


Question:
  
A lens or combination of lenses in which the following defect is completely eliminated is called aplanatic

1.spherical aberration

2.chromatic aberration

3.coma

4.astigmatism.

Posted Date:-2021-05-13 08:27:18


Question:
  
If the whole circle bearing of a line is 270°, its reduced bearing is

1.N 90° W

2. S 90° W

3.W 90°

4. 90° W.

Posted Date:-2021-05-13 08:27:18


Question:
  
In a perfect prismatic compass

1.magnetic axis and geometric axis of the needle coincide

2.ends of the needle and pivot are in same vertical and horizontal planes

3.pivot is vertically over the centre of the graduated circle

4.all the above.

Posted Date:-2021-05-13 08:27:18


Question:
  
In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm The focussing lens is midway between them when a staff 1650 m away is focussed The focal length of the focussing lens, is

1.5.24 cm

2. 6.24 cm

3.7.24 cm

4.8.24 cm

Posted Date:-2021-05-13 08:27:18


Question:
  
Locating the position of a plane table station with reference to three known points, is known as

1.intersection method

2.radiation method

3. resection method

4.three point problem.

Posted Date:-2021-05-13 08:27:18


Question:
  
Location of contour gradient for a high way is best set out from

1.ridge down the hill

2.saddle down the hill

3.bottom to the ridge

4.bottom to the saddle.

Posted Date:-2021-05-13 08:27:18


Question:
  
Staff readings on pegs x and y from X station are 1.755 m and 2.850 m, and from station Y on staff head at Y and X are 0.655 m and 1.560 m. If reduced level of X is 105.5 m, the reduced level of Y is

1.104.0 m

2.104.5 m

3.105.0 m

4.105.5 m

Posted Date:-2021-05-13 08:27:18


Question:
  
The defect of a lens whereby rays of white light proceeding from a point get dispersed into their components and conveyed to various foci, forming a blurred and coloured image is known as

1.chromatic aberration

2.spherical aberration

3.astigmatism

4.coma.

Posted Date:-2021-05-13 08:27:18


Question:
  
The line normal to the plumb line is known as

1.horizontal line

2.level line

3.datum line

4.vertical line.

Posted Date:-2021-05-13 08:27:18


Question:
A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m and 284.295 m respectively, the collimation error per 100 m is

1. 0.015 m

2. 0.030 m

3.0.045 m

4.0.060 m

Posted Date:-2021-05-13 08:27:18


Question:
For taking offsets with an optical square on the right hand side of the chain line, it is held

1.by right hand upside down

2. by left hand upright

3.by right hand upright

4. by left hand up side down.

Posted Date:-2021-05-13 08:27:18


Question:
If deflection angles are measured in a closed traverse, the difference between the sum of the right-hand and that of the left hand angles should be equal to

1.0°

2.90°

3.180°

4.360°

Posted Date:-2021-05-13 08:27:18


Question:
If the declination of the needle is 10° W

1.each of the whole circle reckoning has to be micros by 10°

2.in the quadrantal method, the correction is positive in the 1st and 3rd quadrants

3. in the quadrantal method, the corrections is negative in 2nd and 4th quadrants

4.all the above.

Posted Date:-2021-05-13 08:27:18


Question:
It is more difficult to obtain good results while measuringhorizontal distance by stepping

1.up-hill

2.down-hill

3.in low undulations

4.in plane areas.

Posted Date:-2021-05-13 08:27:18


Question:
Tilt of the staff in stadia tacheometry increases the intercept if it is

1.away from the telescope pointing down hill

2.towards the telescope pointing up-hill

3.away from the telescope pointing up-hill

4.none of these.

Posted Date:-2021-05-13 08:27:18


Question:
Number of links per metre length of a chain are

1.2

2.5

3.8

4.10

Posted Date:-2021-05-13 08:27:18


Question:
Pick up the correct statement from the following :

1.with both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from knots

2.the follower of the chaining operation should be more experienced than the leader

3.at the end of the tenth chain length, the two chain men meet and the ten arrows are handed over to the leader

4.all the above.

Posted Date:-2021-05-13 08:27:18


Question:
Pick up the incorrect statement from the following :

1.while measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length

2.an increase in temperature causes a tape to increase in length and the measured distance is too large

3.the straight distance between end points of a suspended tape is reduced by an amount called the sag correction

4.a 100 m tape of cross section 10 mm x 0.25 mm stretches about 10 mm under 5 kg pull.

Posted Date:-2021-05-13 08:27:18


Question:
Planimeter is used for measuring 

1.volume

2.area

3.contour gradient

4.slope angle

Posted Date:-2021-05-13 08:27:18


Question:
Resolving power of a telescope depends on

1.the diameter of the aperture

2.the pupil aperture of the eye

3.the diameter of the object glass

4.all the above.

Posted Date:-2021-05-13 08:27:18


Question:
Stadia techeometry was discovered by James Watt in the year.

1.1670

2.1770

3.1870

4.1900

Posted Date:-2021-05-13 08:27:18


Question:
Straight, parallel and widely spaced contours represent

1.a steep surface

2.a flat surface

3.an inclined plane surface

4.curved surface.

Posted Date:-2021-05-13 08:27:18


Question:
The additional lines which are measured to show the correctness of the chain surveying are called

1.check clines

2.proof lines

3. tie lines

4. all of these.

Posted Date:-2021-05-13 08:27:18


Question:
The angle of intersection of a curve is the angle between

1.back tangent and forward tangent

2.prolongation of back tangent and forward tangent

3.forward tangent and long chord

4.back tangent and long chord.

Posted Date:-2021-05-13 08:27:18


Question:
The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is

1.502.685 m

2.501.345 m

3.501.340 m

4.504.030 m

Posted Date:-2021-05-13 08:27:18


Question:
The bearing of lines OA and OB are 16° 10' and 332° 18', the value of the included angle BOA is

1.316° 10'

2.158° 28'

3.348° 08'

4.43° 52'

Posted Date:-2021-05-13 08:27:18


Question:
The constant vertical distance between two adjacent contours, is called

1.horizontal interval

2.horizontal equivalent

3.vertical equivalent

4.contour interval

Posted Date:-2021-05-13 08:27:18


Question:
The correction to be applied to each 30 metre chain length along θ° slope, is

1.30 (sec θ - 1) m

2.30 (sin θ - 1) m

3.30 (cos θ - 1) m

4.30 (tan θ - 1) m

Posted Date:-2021-05-13 08:27:18


Question:
The included angles of a theodolite traverse, are generally measured

1. clockwise from the forward station

2. anti-clockwise from the back station

3. anti-clockwise from the forward station

4.clockwise from the back station.

Posted Date:-2021-05-13 08:27:18


Question:
The method generally preferred to for contouring an undulating area, is

1.chain surveying

2.plane table surveying

3.tacheometrical surveying

4.compass surveying.

Posted Date:-2021-05-13 08:27:18


Question:
The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is

1. 3.290 m

2.3.300 m

3.3.275 m

4.2.790 m

Posted Date:-2021-05-13 08:27:18


Question:
The staff reading at a distance of 80 m from a level with the bubble at its centre is 1.31 m. When the bubble is moved by 5 divisions out of the centre, the reading is 1.39 m. The angular value of the one division of the bubble, is

1.28.8 seces

2.41.25 secs

3.14.52 secs

4.25.05 secs

Posted Date:-2021-05-13 08:27:18


Question:
The theodolites used for making tacheometric observations by optical wedge system, are

1.provided with stadia hairs in front of eye piece

2.not provided with stadia hairs at all

3.fitted with a glass wedge inside the telescope

4.fitted with a glass wedge in front of telescope.

Posted Date:-2021-05-13 08:27:18


Question:
To orient a plane table at a point with two inaccessible points, the method generally adopted, is

1.intersection

2.resection

3.radiation

4.two point problem.

Posted Date:-2021-05-13 08:27:18


Question:
Under ordinary conditions, the precision of a theodolite traverse is affected by

1.systematic angular errors

2.accidental linear errors

3.systematic linear errors

4. accidental angular errors.

Posted Date:-2021-05-13 08:27:18


Question:
While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be

1.0.02 cm

2. 0.15 cm

3. 02 cm

4. 0.1 cm

Posted Date:-2021-05-13 08:27:18


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
  106. Basic Civil Engineering MCQ
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!