Engineering/Civil Engineering MCQS-Surveying Section 5 Sample Test,Sample questions

Question:
 
A sewer is laid from a manhole A to a manhole B, 250 m away along a gradient of 1 in 125. If the reduced level of the invert at A is 205.75 m and the height of the boning rod is 3 m, the reduced level of the sight rail at B, is

1.208.75 m

2. 202.75 m

3.206.75 m

4.211.75 m

Posted Date:-2021-05-13 01:21:25


Question:
 
If the whole circle bearing of a line is 180°, its reduced bearing is

1. S 0° E

2.S 0° W

3.S

4.N.

Posted Date:-2021-05-13 01:21:25


Question:
 
Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to

1.shift

2. twice the shift

3.thrice the shift

4.four times the shift.

Posted Date:-2021-05-13 01:21:25


Question:
 
Rankine's deflection angle in minutes is obtained by multiplying the length of the chord by

1.degree of the curve

2. square of the degree of the curve

3. inverse of the degree of the curve

4. none of these.

Posted Date:-2021-05-13 01:21:25


Question:
 
Short offsets are measured with

1.an ordinary chain

2.an invar tape

3.a metallic tape

4.a steel tape.

Posted Date:-2021-05-13 01:21:25


Question:
 
The line of sight is kept as high above ground surface as possible to minimise the error in the observed angles due to

1.shimmering

2.horizontal refraction

3.vertical refraction

4.both shimmering and horizontal refraction.

Posted Date:-2021-05-13 01:21:25


Question:
  
If a linear traverse follows a sharp curve round a large lake where it is difficult to have long legs, the accuracy of the traverse may be improved by

1.taking short legs

2.making repeated observations of angular and linear measurements

3. making a subsidiary traverse to determine the length of a long leg

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
  
If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for

1.horizontal sights

2. inclined sights upward

3. inclined sight downward

4.none of these.

Posted Date:-2021-05-13 01:21:25


Question:
  
Mistakes which may produce a very serious effect upon the final results arise due to

1. in attention

2.in experience

3.carelessness

4.all of these.

Posted Date:-2021-05-13 01:21:25


Question:
  
Number of subdivisions per metre length of a levelling staff is

1.100

2.200

3.500

4.1000

Posted Date:-2021-05-13 01:21:25


Question:
  
The distance between terminal points computed from a subsidiary traverse run between them, is generally known, as

1.traverse leg

2.a base

3.traverse base

4. all the above.

Posted Date:-2021-05-13 01:21:25


Question:
  
You have to observe an included angle with better accuracy than what is achievable by a vernier, you will prefer the method of

1.repetition

2.reiteration

3.double observations

4.exactness.

Posted Date:-2021-05-13 01:21:25


Question:
A well conditioned triangle has no angle less than

1.20°

2.30°

3.45°

4.60°.

Posted Date:-2021-05-13 01:21:25


Question:
Bergchrund is a topograhical feature in

1. plains

2.water bodies

3.hills

4.glaciated region

Posted Date:-2021-05-13 01:21:25


Question:
Chain surveying is well adopted for

1. small areas in open ground

2.small areas with crowded details

3.large areas with simple details

4.large areas with difficult details.

Posted Date:-2021-05-13 01:21:25


Question:
Check lines (or proof lines) in Chain Surveying, are essentially required

1.to plot the chain lines

2. to plot the offsets

3. to indicate the accuracy of the survey work

4. to increase the out-turn

Posted Date:-2021-05-13 01:21:25


Question:
Contour lines of different elevations can unite to form one line, only in the case of

1.a vertical cliff

2.a saddle

3.a water shed line

4.a hill top.

Posted Date:-2021-05-13 01:21:25


Question:
Designation of a curve is made by :

1.angle subtended by a chord of any length

2.angle subtended by an arc of specified length

3.radius of the curve

4. curvature of the curve.

Posted Date:-2021-05-13 01:21:25


Question:
During secular variation of magnetic meridian at different places

1.range of oscillations is constant

2.period of oscillation is constant

3.range and period of oscillation both vary

4.period of oscillation only varies.

Posted Date:-2021-05-13 01:21:25


Question:
For high sensivity of the bubble tube

1.a liquid of low viscosity is used

2. a liquid of low surface tension is used

3. the bubble space should be long

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
For indirect ranging, number of ranging rods required, is

1.1

2.2

3.3

4.4

Posted Date:-2021-05-13 01:21:25


Question:
For locating a distant object visible from two transit stations, the method usually preferred to, is

1.Angles and distances from transit stations

2.Angles from two transit stations

3.distance from two transit stations

4.Angle from one transit station and distance from the other.

Posted Date:-2021-05-13 01:21:25


Question:
In a closed traverse, sum of south latitudes exceeds the sum of north latitudes and the sum of east departures exceeds the sum of west departures, then, the closing line will lie in

1.north-west quadrant

2.north east quadrant

3.south-east quadrant

4.south-west quadrant.

Posted Date:-2021-05-13 01:21:25


Question:
Pick up the correct statement from the following

1.1 second of arc corresponds to a displacement ratio of 1:206, 300

2.1 degree of arc corresponds to a displacement ratio of 1:57

3.the angular errors tend to propagate themselves along a traverse as the square root of the number of stations

4. all the above.

Posted Date:-2021-05-13 01:21:25


Question:
Pick up the correct statement from the following :

1. the diaphragm is placed between eyepiece and the objective but nearer to the former

2.the diaphragm is placed between the eyepiece and objective but nearer to the later

3.the outer component of the objective is a double-convex lens of crown glass

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
Profile levelling is usually done for determining

1.contours of an area

2.capacity of a reservoir

3.elevations along a straight line

4.boundaries of property

Posted Date:-2021-05-13 01:21:25


Question:
Prolongation of chain line across an obstruction in chain surveying, is done by

1.making angular measurements

2.drawing perpendiculars with a chain

3. solution of triangles

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
Subtense tacheometry is generally preferred to if ground is

1.flat

2.undulating

3.mountaineous

4.deserts.

Posted Date:-2021-05-13 01:21:25


Question:
The chaining on sloping ground is

1.easier along the falling gradient

2.easier along the up gradient

3.equally convenient along falling as well as up gradient

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
The chord of a curve less than peg interval, is known as

1.small chord

2.sub-chord

3.normal chord

4.short chord.

Posted Date:-2021-05-13 01:21:25


Question:
The Huygen's telescope eye piece

1.is aplanatic

2.achromatic

3.both (a) and (b)

4.neither (a) nor (b).

Posted Date:-2021-05-13 01:21:25


Question:
The line of collimation method of reduction of levels, does not provide a check on

1. intermediate sights

2.fore sights

3.back sights

4.reduced levels.

Posted Date:-2021-05-13 01:21:25


Question:
The method of reversal

1.is usually directed to examine whether a certain part is truly parallel or perpendicular to another

2. makes the erroneous relationship between parts evident

3.both (a) and (b)

4.neither (a) nor (b).

Posted Date:-2021-05-13 01:21:25


Question:
The operation of resection involves the following steps

rough orientation of the plane table
the three lines form a triangle of error
drawing lines back through the three control points
select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise
the points obtained by three rays is the correct location.

The correct sequence is

1.1, 3, 2, 4, 5

2. 1, 2, 3, 4, 5

3.1, 4, 3, 2, 5

4. 1, 4, 2, 3, 5

Posted Date:-2021-05-13 01:21:25


Question:
The operation of revolving a plane table about its vertical axis so that all lines on the sheet become parallel to corresponding lines on the ground, is known

1.levelling

2.centering

3.orientation

4.setting.

Posted Date:-2021-05-13 01:21:25


Question:
The ratio of the distances at which a stated length can be distinguished by the telescope and the human eye, respectively, is called

1.brightness of telescope

2.magnification of telescope

3.resolving power of telescope

4. none of these.

Posted Date:-2021-05-13 01:21:25


Question:
The smaller horizontal angle between the true meridian and a survey line, is known

1.declination

2.bearing

3.azimuth

4.dip.

Posted Date:-2021-05-13 01:21:25


Question:
There are two stations A and B. Which of the following statements is correct :

1.. the fore bearing of AB is AB

2.the back bearing of AB is BA

3. the fore and back bearings of AB differ by 180°

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
To avoid large centering error with very short legs, observations are generally made

1.to chain pins

2.by using optical system for centering the theodolite

3.to a target fixed on theodolite tripod on which theodolite may be fitted easily

4.all the above.

Posted Date:-2021-05-13 01:21:25


Question:
To orient a plane table at a point P roughly south of the mid-point of two inaccessible conical hill stations A and B in the plains, a point C is selected in line with AB and table is oriented at C by bringing ab in line with AB. A ray is then drawn towards P and at P the table is oriented by back ray method. The orientation so obtained, is

1.unique and correct

2.incorrect

3.manifold and correct

4.not reliable.

Posted Date:-2021-05-13 01:21:25


Question:
Which one of the following statements is correct ?

1.when the axes of rotation of the graduated circle and the verniers are not coincident, the instrument possesses eccentricity

2.the mean of the readings of the two verniers gives correct reading free from the eccentricity

3.one vernier may be used if the readings of two verniers differ by a constant

4. all the above.

Posted Date:-2021-05-13 01:21:25


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!