Engineering/Compressors,%20Gas%20Turbines%20and%20Jet%20Engines%20MCQ%20Practice%20Test%20-%20Set%2003 Sample Test,Sample questions

Question:
 A compressor at high altitudes will require ________ power.

1.Same

2.Less

3.More

4. None of these

Posted Date:-2021-11-25 15:44:44


Question:
 A turboprop is preferred to turbojet because

1. It has high propulsive efficiency at high speeds

2.It can fly at supersonic speeds

3. It can fly at high elevations

4.It has high power for take off

Posted Date:-2021-11-25 15:28:19


Question:
 An after-cooler is used to

1.Remove impurities from air

2.Reduce volume of air

3.Cause moisture and oil vapour to drop out

4. Cool the air

Posted Date:-2021-11-25 16:58:49


Question:
 Atmospheric pressure is 1.03 kg/cm and vapour pressure is 0.03 kg/cm. The air pressure will be

1.1.03 kg/cm²

2.1.06 kg/cm²

3.1.00 kg/cm²

4.0.53 kg/cm²

Posted Date:-2021-11-25 15:38:19


Question:
 For an irreversible gas turbine cycle, the efficiency and work ratio both depend on

1.Pressure ratio alone

2.Maximum cycle temperature alone

3.Minimum cycle temperature alone

4. Both pressure ratio and maximum cycle temperature

Posted Date:-2021-11-25 17:12:29


Question:
 For maximum work, the reheating should be done to an intermediate pressure of
      (Where p₁ = Maximum pressure, and p₂ = Minimum pressure)

1. (p₁ - p₂)/2

2.(p₁ + p₂)/2

3. p₁/p₂

4.p₁ p₂

Posted Date:-2021-11-25 15:39:31


Question:
 In a centrifugal compressor, an increase in speed at a given pressure ratio causes

1.Increase in flow

2.Decrease in flow

3. Increase in efficiency

4.Increase in flow and decrease in efficiency

Posted Date:-2021-11-25 15:36:57


Question:
 In a single stage, single acting reciprocating air compressor without clearance volume, the work-done is maximum during

1.Isothermal compression

2.Isentropic compression

3.Polytropic compression

4.None of these

Posted Date:-2021-11-25 17:18:09


Question:
 Inter-cooling in multistage compressors is done

1.To cool the air during compression

2.To cool the air at delivery

3.To enable compression in two stages

4.To minimize the work of compression

Posted Date:-2021-11-25 16:27:20


Question:
 Open cycle gas turbine works on
(A) 

1.Brayton or Atkinson cycle

2.Rankine cycle

3.Carnot cycle

4.Ericsson cycle

Posted Date:-2021-11-25 16:06:50


Question:
 Pick up the wrong statement

1.Centrifugal compressors deliver practically constant pressure over a considerable range of capacities

2.Axial flow compressors have a substantially constant delivery at variable pressures

3.Centrifugal compressors have a wider stable operating range than axial flow compressors

4.Axial flow compressors are bigger in diameter compared to centrifugal type

Posted Date:-2021-11-25 15:45:58


Question:
 Temperature of gases at end of compression as compared to exhaust gases in a gas turbine is

1.Higher

2.Lower

3.Equal

4.Can’t be compared

Posted Date:-2021-11-25 17:04:59


Question:
 The degree of reaction in an axial flow compressor is defined as the ratio of static enthalpy rise in the

1.Rotor to static enthalpy rise in the stator

2.Stator to static enthalpy rise in the rotor

3.Rotor to static enthalpy rise in the stage

4.Stator to static enthalpy rise in the stage

Posted Date:-2021-11-25 16:11:37


Question:
 The material commonly used for air craft gas turbine is

1.Stainless steel

2.High alloy steel

3.Duralumin

4.Timken, Haste alloys

Posted Date:-2021-11-25 17:08:11


Question:
 The material commonly used for air craft gas turbine is

1.Stainless steel

2.High alloy steel

3.Duralumin

4.Timken, Haste alloys

Posted Date:-2021-11-25 17:08:28


Question:
 The work ratio of simple gas turbine cycle depends on

1.Pressure ratio

2.Maximum cycle temperature

3.Minimum cycle temperature

4.All of the above

Posted Date:-2021-11-25 15:59:29


Question:
A closed gas turbine in which fuel is burnt directly in the air is not possible because of

1.Paucity of O2

2.Increasing gas temperature

3. High specific volume

4.High friction losses

Posted Date:-2021-11-25 17:28:56


Question:
A gas turbine used in air craft should have

1.High h.p. and low weight

2.Low weight and small frontal area

3.Small frontal area and high h.p.

4.High speed and high h.p.

Posted Date:-2021-11-25 17:20:28


Question:
A jet engine has

1. No propeller

2.Propeller in front

3.Propeller at back

4.Propeller on the top

Posted Date:-2021-11-25 17:07:20


Question:
A jet engine works on the principle of conservation of

1.Mass

2.Energy

3.Flow

4.Linear momentum

Posted Date:-2021-11-25 17:32:47


Question:
A large clearance volume in a reciprocating compressor results in

1.Increased volume flow rate

2.Reduced volume flow rate

3. Lower suction pressure

4. Lower delivery pressure

Posted Date:-2021-11-25 16:24:58


Question:
Actual compression curve is

1.Same as isothermal

2.Same as adiabatic

3.Better than isothermal and adiabatic

4. In between isothermal and adiabatic

Posted Date:-2021-11-25 15:35:46


Question:
Axial flow compressor has the following advantage over centrifugal compressor

1.Larger air handling ability per unit frontal area

2.Higher pressure ratio per stage

3.Aerofoil blades are used

4.Higher average velocities

Posted Date:-2021-11-25 15:33:02


Question:
Axial flow compressor resembles

1. Centrifugal pump

2. Reciprocating pump

3.Turbine

4.Sliding vane compressor

Posted Date:-2021-11-25 15:30:18


Question:
Choose the correct statement

1.Gas turbine requires lot of cooling water

2.Gas turbine is capable of rapid start up and loading

3.Gas turbines has flat efficiency at part loads

4.Gas turbines have high standby losses and require lot of maintenance

Posted Date:-2021-11-25 17:30:29


Question:
Euler's equation can be used for

1.Radial flow compressors

2.Axial flow compressors

3.Pumps

4.All of the above

Posted Date:-2021-11-25 15:49:24


Question:
Gas turbine blades are given a rake

1.Equal to zero

2.In the direction of motion of blades

3.Opposite to the direction of motion of blades

4.Depending on the velocity

Posted Date:-2021-11-25 17:02:06


Question:
Gas turbine blades are given a rake

1.Equal to zero

2.In the direction of motion of blades

3.Opposite to the direction of motion of blades

4.Depending on the velocity

Posted Date:-2021-11-25 17:02:07


Question:
If the flow of air through the compressor is parallel to its axis, then the compressor is

1. Reciprocating compressor

2.Centrifugal compressor

3.Axial flow compressor

4. Turbo compressor

Posted Date:-2021-11-25 15:43:24


Question:
In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in ________ of the piston.
(A) One stroke
(B) Two strokes
(C)
(D)

1.One stroke

2.Two strokes

3. Three strokes

4. Four strokes

Posted Date:-2021-11-25 16:05:20


Question:
In air compressors, free air delivery means the

1.Actual volume of the air delivered by the compressor when reduced to normal temperature and pressure conditions

2.Volume of air delivered by the compressor

3.Volume of air sucked by the compressor during its suction stroke

4.None of the above

Posted Date:-2021-11-25 15:25:48


Question:
In open cycle turbojet engines used in military aircraft, reheating the exhaust gas from the turbine by burning, more fuel is used to increase the

1.Thrust and range of aircraft

2.Efficiency of the engine

3. Both (A) and (B)

4.None of these

Posted Date:-2021-11-25 17:09:21


Question:
In the axial flow gas turbine, the work ratio is the ratio of

1. Compressor work and turbine work

2.Output and input

3.Actual total head temperature drop to the isentropic total head drop from total head inlet to static head outlet

4.Actual compressor work and theoretical compressor work

Posted Date:-2021-11-25 17:23:21


Question:
In the cross compounding of the gas turbine plant

1.H.P. compressor is connected to H.P. turbine and L.P. compressor to L.P. turbine

2.H.P. compressor is connected to L.P. turbine and L.P. compressor is connected to H.P. turbine

3. Both the arrangements can be employed

4.All are connected in series

Posted Date:-2021-11-25 17:31:37


Question:
It is not possible to use closed gas turbine cycle in aeronautical engines because

1.It is inefficient

2.It is bulky

3.It requires cooling water for its operation

4.None of the above

Posted Date:-2021-11-25 17:10:19


Question:
Pick up the wrong statement

1. Large gas turbines employ axial flow compressors

2.Axial flow compressors are more stable than centrifugal type compressors but not as efficient

3.Axial flow compressors have high capacity and efficiency

4.Axial flow compressors have instability region of operation

Posted Date:-2021-11-25 17:26:12


Question:
Pick up wrong statement. Surging phenomenon in centrifugal compressor depends on

1.Mass flow rate

2.Pressure ratio

3. Change in load

4.Stagnation pressure at the outlet

Posted Date:-2021-11-25 15:24:05


Question:
Producer gas is produced by

1.Carbonisation of coal

2.Passing steam over incandescent coke

3.Passing air and a large amount of steam over waste coal at about 65°C

4.Partial combustion of coal, coke, anthracite coal or charcoal in a mixed air steam blast

Posted Date:-2021-11-25 17:15:01


Question:
Separators are generally used in air compressor installations

1.Before the inter-cooler

2.After the inter-cooler

3.Between the after-cooler and receiver

4.Before first stage suction

Posted Date:-2021-11-25 17:13:36


Question:
The air-fuel ratio in gas turbines is of the order of

1.7: 1

2. 15: 1

3. 30: 1

4.50: 1.

Posted Date:-2021-11-25 16:25:58


Question:
The combustion efficiency of a gas turbine using perfect combustion chamber is of the order of

1.75%

2.85%

3.90%

4.99%

Posted Date:-2021-11-25 17:11:29


Question:
The compression ratio for the compressor is always _________ unity.

1. Equal to

2. Less than

3.More than

4.None of these

Posted Date:-2021-11-25 15:47:04


Question:
The degree of reaction of an axial flow turbine is the ratio of isentropic temperature drop in a blade row to the

1.Adiabatic temperature drop in the stage

2. Total temperature drop

3.Total temperature drop in the stage

4.Total adiabatic temperature drop

Posted Date:-2021-11-25 17:24:31


Question:
The efficiency of a jet engine is higher at

1.Low speeds

2.High speeds

3.Low altitudes

4.High altitudes

Posted Date:-2021-11-25 16:01:16


Question:
The efficiency of roots blower ________ with the increase in pressure ratio.

1.Decreases

2.Increases

3.Does not change

4.None of these

Posted Date:-2021-11-25 15:31:17


Question:
The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is

1.Heated

2.Compressed air before entering the combustion chamber is heated

3.Bled gas from turbine is heated and readmitted for complete expansion

4.Exhaust gases drive the compressor

Posted Date:-2021-11-25 17:00:56


Question:
The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is

1.Heated

2.Compressed air before entering the combustion chamber is heated

3.Bled gas from turbine is heated and readmitted for complete expansion

4.Exhaust gases drive the compressor

Posted Date:-2021-11-25 17:01:00


Question:
The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is

1.Heated

2.Compressed air before entering the combustion chamber is heated

3.Bled gas from turbine is heated and readmitted for complete expansion

4.Exhaust gases drive the compressor

Posted Date:-2021-11-25 17:01:08


Question:
The fuel consumption in gas turbines is accounted for by

1. Lower heating value

2.Higher heating value

3.Heating value

4. Higher calorific value

Posted Date:-2021-11-25 16:10:16


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:18


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:19


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:23


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:26


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:30


Question:
The inlet pressure is always ________ the discharge pressure.

1. Equal to

2.Less than

3.More than

4. None of these

Posted Date:-2021-11-25 17:03:40


Question:
The maximum temperature in a gas turbine is

1.200°C

2. 500°C

3.700°C

4.1000°C

Posted Date:-2021-11-25 15:34:23


Question:
The power available for takeoff and climb in case of turbojet engine as compared to reciprocating engine is

1.Less

2.More

3.Same

4.May be less or more depending on ambient conditions

Posted Date:-2021-11-25 17:27:19


Question:
The pressure ratio for an open cycle gas turbine compared to closed cycle gas turbine of same h.p. is

1. Low

2.High

3.Same

4.Low/high depending on make and type

Posted Date:-2021-11-25 16:02:22


Question:
The pressure ratio in gas turbines is of the order of

1. 2: 1

2.4:1

3.61: 1

4. 9: 1

Posted Date:-2021-11-25 16:28:16


Question:
The pressure ratio of an ideal vaned compressor with increase in mass flow rate

1.Increases

2.Decreases

3.Remain constant

4.First decreases and then increases

Posted Date:-2021-11-25 15:40:38


Question:
The ratio of the increase in pressure in rotor blades to total increase in pressure in the stage is called

1.Pressure ratio

2.Pressure coefficient

3.Degree of reaction

4.Slip factor

Posted Date:-2021-11-25 15:27:06


Question:
The ratio of the indicated power to the shaft power or brake power of the motor or engine required to drive the compressor, is called

1.Compressor efficiency

2.Volumetric efficiency

3. Isothermal efficiency

4.Mechanical efficiency

Posted Date:-2021-11-25 15:55:47


Question:
The thermal efficiency of a gas turbine as compared to a diesel plant is

1.Same

2.More

3.Less

4.Depends on other factors

Posted Date:-2021-11-25 16:15:25


Question:
The volume of air delivered by the compressor is called

1.Free air delivery

2.Compressor capacity

3.Swept volume

4.None of these

Posted Date:-2021-11-25 17:05:53


Question:
The volumetric efficiency for reciprocating air compressors is about

1. 10 to 40%

2.40 to 60%

3.60 to 70%

4.70 to 90%

Posted Date:-2021-11-25 17:22:02


Question:
The work ratio of a gas turbine plant is defined as the ratio of

1.Net work output and heat supplied

2.Net work output and work done by turbine

3.Actual heat drop and isentropic heat drop

4.Net work output and isentropic heat drop

Posted Date:-2021-11-25 15:48:18


Question:
The work ratio of simple gas turbine cycle depends on

1.Pressure ratio

2.Maximum cycle temperature

3.Minimum cycle temperature

4. All of the above

Posted Date:-2021-11-25 15:56:48


Question:
Water gas is produced by

1.Carbonisation of coal

2. Passing steam over incandescent coke

3.Passing air and a large amount of steam over waste coal at about 65°C

4.Partial combustion of coal, eke, anthracite coal or charcoal in a mixed air steam blast

Posted Date:-2021-11-25 17:16:45


Question:
Water is injected in gas turbine cycle to

1.Control temperature

2.Control output of turbine

3.Control fire hazards

4.Increase efficiency

Posted Date:-2021-11-25 17:19:20


Question:
When the outlet angle from the rotor of a centrifugal compressor is more than 90°, then the blades are said to be

1.Forward curved

2.Backward curved

3.Radial

4.None of these

Posted Date:-2021-11-25 16:59:48


Question:
Which of the following fuels can be used in turbojet engines?

1.Liquid hydrogen

2.High speed diesel oil

3.Kerosene

4.Methyl alcohol

Posted Date:-2021-11-25 17:34:25


Question:
Which of the following statement is correct relating to rocket engines?

1.The combustion chamber in a rocket engine is directly analogous to the reservoir of a supersonic wind tunnel

2. The stagnation conditions exist at the combustion chamber

3.The exit velocities of exhaust gases are much higher than those in jet engine

4. All of the above

Posted Date:-2021-11-25 16:14:04


Question:
Which of the following statement is wrong?

1.In a two stage reciprocating air compressor with complete intercooling, maximum work is saved

2.The minimum work required for a two stage reciprocating air compressor is double the work required for each stage

3. The ratio of the volume of free air delivery per stroke to the swept volume of the piston is called volumetric efficiency

4.None of the above

Posted Date:-2021-11-25 16:08:26


Question:
Which of the following statement is wrong?

1. In a two stage reciprocating air compressor with complete intercooling, maximum work is saved

2. The minimum work required for a two stage reciprocating air compressor is double the work required for each stage

3.The ratio of the volume of free air delivery per stroke to the swept volume of the piston is called volumetric efficiency

4.None of these

Posted Date:-2021-11-25 16:09:20


Question:
With the decrease in compression ratio, the volumetric efficiency

1.Does not change

2.Increases

3.Decreases

4.First decrease and then increase

Posted Date:-2021-11-25 15:20:50


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
  106. Basic Civil Engineering MCQ
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!