Engineering/Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01 Sample Test,Sample questions

Question:
 If the flow of air through the compressor is perpendicular to its axis, then it is a

1.Reciprocating compressor

2.Centrifugal compressor

3.Axial flow compressor

4.Turbo compressor

Posted Date:-2021-11-24 16:03:13


Question:
 In a double acting compressor, the air is compressed

1. In one cylinder

2. In two cylinders

3. In a single cylinder on both sides of the piston

4.In two cylinders on both sides of the piston

Posted Date:-2021-11-24 17:25:28


Question:
 Separators in compressor installations are located

1.Before inter-cooler

2.After inter-cooler

3.After receiver

4. Between after-cooler and air receiver

Posted Date:-2021-11-24 17:16:44


Question:
 The overall thermal efficiency of an ideal gas turbine plant is (where r = Pressure ratio)

1.r ɣ-1

2. 1 - r ɣ-1

3. 1 - (1/r) ɣ-1/ɣ

4.1 - (1/r) ɣ/ɣ-1

Posted Date:-2021-11-24 16:17:13


Question:
. Reciprocating air compressor is best suited for

1.Large quantity of air at high pressure

2.Small quantity of air at high pressure

3. Small quantity of air at low pressure

4.Large quantity of air at low pressure

Posted Date:-2021-11-24 17:24:27


Question:
A compressor mostly used for supercharging of I.C. engines is

1.Radial flow compressor

2. Axial flow compressor

3.Roots blower

4.Reciprocating compressor

Posted Date:-2021-11-24 16:24:30


Question:
After-cooler is used to

1. Cool the air

2.Decrease the delivery temperature for ease in handling

3. Cause moisture and oil vapour to drop out

4.Reduce volume

Posted Date:-2021-11-24 17:26:33


Question:
Gas turbines use following type of air compressor

1. Centrifugal type

2.Reciprocating type

3.Lobe type

4.Axial flow type

Posted Date:-2021-11-24 16:05:24


Question:
In a closed cycle gas turbine, the air is compressed

1.Isothermally

2.Polytropically

3.Isentropically

4.None of these

Posted Date:-2021-11-24 16:08:09


Question:
In a jet propulsion unit, the products of combustion after passing through the gas turbine are discharged into

1.Atmosphere

2.Vacuum

3.Discharge nozzle

4.Back to the compressor

Posted Date:-2021-11-24 16:31:14


Question:
In an axial flow compressor, the ratio of pressure in the rotor blades to the pressure rise in the compressor in one stage is known as

1.Work factor

2. Slip factor

3.Degree of reaction

4.Pressure coefficient

Posted Date:-2021-11-24 16:33:16


Question:
In jet engines, for the efficient production of large power, fuel is burnt in an atmosphere of

1.Vacuum

2.Atmospheric air

3.Compressed air

4.Oxygen alone

Posted Date:-2021-11-24 16:25:29


Question:
In multistage compressor, the isothermal compression is achieved by

1. Employing inter-cooler

2.By constantly cooling the cylinder

3.By running compressor at very slow speed

4. By insulating the cylinder

Posted Date:-2021-11-24 17:11:44


Question:
In the aircraft propellers

1.The propulsive matter is caused to flow around the propelled body

2.Propulsive matter is ejected from within the propelled body

3.Its functioning does not depend on presence of air

4.All of the above

Posted Date:-2021-11-24 16:29:17


Question:
Mining industry usually employs following motive power

1. A.C. electric motor

2.Compressed air

3.Petrol engine

4.Diesel engine

Posted Date:-2021-11-24 17:28:31


Question:
Out of the following, from where you will prefer to take intake for air compressor

1.0.1 bar and 20°C

2.1 bar and 20°C

3.0.1 bar and 40°C

4.1 bar and 40°C

Posted Date:-2021-11-24 17:08:11


Question:
Out of the following, from where you will prefer to take intake for air compressor

1. From an air conditioned room maintained at 20°C

2.From outside atmosphere at 1°C

3. From coal yard side

4.From a side where cooling tower is located nearby

Posted Date:-2021-11-24 17:09:38


Question:
Pick up the correct statement

1.Large gas turbines use radial inflow turbines

2.Gas turbines have their blades similar to steam turbine

3.Gas turbine's blade will appear as impulse section at the hub and as a reaction section at tip

4.Gas turbines use both air and liquid cooling

Posted Date:-2021-11-24 16:21:04


Question:
Pick up the wrong statement

1. Pulse-jet requires no ambient air for propulsion

2. Ramjet engine has no turbine

3.Turbine drives compressor in a Turbojet

4.Bypass turbojet engine increases the thrust without adversely affecting, the propulsive efficiency and fuel economy

Posted Date:-2021-11-24 17:18:27


Question:
Ram compression in turbojet involves

1. Reduction of speed of incoming air and conversion of part of it into pressure energy

2.Compression of inlet air

3. Increasing speed of incoming air

4.Lost work

Posted Date:-2021-11-24 16:23:29


Question:
Reciprocating air compressor is best suited for

1.Large quantity of air at high pressure

2. Small quantity of air at high pressure

3.Small quantity of air at low pressure

4.Large quantity of air at low pressure

Posted Date:-2021-11-24 17:21:17


Question:
Reheating in a multistage expansion gas turbine ________ compressor work.

1.Has no effect on

2.Decreases

3.Increases

4.None of these

Posted Date:-2021-11-24 17:14:51


Question:
Standard air is the air at ________ and relative humidity of 36 percent.

1.0.1 bar and 20°C

2.1 bar and 20°C

3.0.1 bar and 40°C

4.1 bar and 40°C

Posted Date:-2021-11-24 17:06:59


Question:
The area of actual indicator diagram on an air compressor as compared to area of ideal indicator diagram is

1.Less

2.More

3.Same

4.More/less depending on compressor capacity

Posted Date:-2021-11-24 17:14:04


Question:
The capacity of compressor will be highest when its intake temperature is

1. Lowest

2.Highest

3.Anything

4.Atmospheric

Posted Date:-2021-11-24 17:01:37


Question:
The closed cycle in gas turbines

1.Provides lesser flexibility

2.Provides lesser flexibility

3.In never used

4.Is used when gas is to be burnt

Posted Date:-2021-11-24 16:15:29


Question:
The closed cycle in gas turbines

1.Provides greater flexibility

2.Provides lesser flexibility

3. In never used

4.Is used when gas is to be burnt

Posted Date:-2021-11-24 16:09:25


Question:
The compressor capacity is defined as the

1.Actual volume of the air delivered by the compressor when reduced to normal temperature and pressure conditions

2.Volume of air delivered by the compressor

3.Volume of air sucked by the compressor during its suction stroke

4. None of the above

Posted Date:-2021-11-24 17:13:01


Question:
The degree of reaction is usually kept ________ for all types of axial flow compressors.

1.0.2

2.0.3

3. 0.4

4.0.5

Posted Date:-2021-11-24 16:22:02


Question:
The efficiency and work ratio of a gas turbine plant can be increased by

1.Adding heat exchanger

2.Injecting water in/around combustion chamber

3.Reheating the air after partial expansion in the turbine

4.All of the above

Posted Date:-2021-11-24 16:37:05


Question:
The gas in cooling chamber of a closed cycle gas turbine is cooled at

1. Constant volume

2.Constant temperature

3.Constant pressure

4.None of these

Posted Date:-2021-11-24 16:06:29


Question:
The maximum combustion pressure in gas turbine as compared to I.C. engine is

1.More

2.Less

3.Same

4.Depends on other factors

Posted Date:-2021-11-24 16:07:19


Question:
The overall isothermal efficiency of the compressor is defined as the ratio of

1.Work required to compress the air isothermally to the actual work required to compress the air for the same pressure ratio

2. Isothermal power to the shaft power or B.P. of the motor or engine required to drive the compressor

3.Volume of free air delivery per stroke to the swept volume of the piston

4. Isentropic power to the power required to drive the compressor

Posted Date:-2021-11-24 17:19:41


Question:
The reason for volumetric efficiency of reciprocating compressor being less than 100 percent is

1.Pressure drop across the valves

2.Superheating in compressor

3.Clearance volume and leakages

4.All of the above

Posted Date:-2021-11-24 17:29:45


Question:
The volume of air sucked by the compressor during its suction stroke is called

1.Free air delivery

2.Compressor capacity

3.Swept volume

4.None of these

Posted Date:-2021-11-24 17:03:18


Question:
The volumetric efficiency of a compressor

1. Increases with decrease in compression ratio

2.Decreases with decrease in compression ratio

3. Increases with increase in compression ratio

4.Decreases with increase in compression ratio

Posted Date:-2021-11-24 16:35:30


Question:
The work-done on a compressor will be minimum if air is taken from

1.The atmosphere

2.A source at 0° C

3. A source of low temperature air

4.A source of high temperature air

Posted Date:-2021-11-24 16:26:40


Question:
To avoid moisture troubles, the branch connections from compressed air lines should be taken from

1.Top side of main

2.Bottom side of main

3.Left side of main

4.Right side of main

Posted Date:-2021-11-24 16:32:24


Question:
To avoid moisture troubles, the compressed air main line should

1.Rise gradually towards the point of use

2.Drop gradually towards the point of use

3.Be laid vertically

4.Be laid exactly horizontally

Posted Date:-2021-11-24 16:34:27


Question:
When air is to be compressed at a high pressure, then it is advantageous to use

1.Single stage compression

2.Multistage compression without intercooling

3.Multistage compression with intercooling

4.None of these

Posted Date:-2021-11-24 17:10:47


Question:
Which is false statement about multistage compression?

1.Power consumption per unit of air delivered is low

2.Volumetric efficiency is high

3. It is best suited for compression ratios around 7:1

4.The moisture in air is condensed in the inter-cooler

Posted Date:-2021-11-24 17:05:11


Question:
Which of the following statement is correct?

1.The reciprocating compressors are best suited for high pressure and low volume capacity

2.The effect of clearance volume on power consumption is negligible for the same volume of discharge

3.Both (A) and (B)

4.None of these

Posted Date:-2021-11-24 17:27:21


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
Search
R4R Team
R4Rin Top Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on R4R.in website is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!